Menu

Important: This documentation is about an older version. It's relevant only to the release noted, many of the features and functions have been updated or replaced. Please view the current version.

Open source

Migrate from Consul to memberlist KV store for hash rings without downtime

Mimir Jsonnet uses memberlist as KV store for hash rings since Mimir 2.2.0.

Memberlist can be disabled by using the following configuration:

jsonnet
{
  _config+:: {
    memberlist_ring_enabled: false
  }
}

If you are running Mimir hash rings with Consul and would like to migrate to memberlist without any downtime, you can follow instructions in this document.

Step 1: Enable memberlist and multi KV store.

jsonnet
{
  _config+:: {
    memberlist_ring_enabled: true,
    multikv_migration_enabled: true,
  }
}

Step 1 configures components to use multi KV store, with consul as primary and memberlist as secondary stores. This step requires rollout of all Mimir components. After applying this step all Mimir components will expose /memberlist page on HTTP admin interface, which can be used to check health of memberlist cluster.

Step 2: Enable KV store mirroring

jsonnet
{
  _config+:: {
    memberlist_ring_enabled: true,
    multikv_migration_enabled: true,
    multikv_mirror_enabled: true,  // Changed in this step.
  }
}

In this step we enable writes to primary KV store (Consul) to be mirrored into secondary store (memberlist). Applying this change will not cause restart of Mimir components.

You can monitor following metrics to check if mirroring was enabled on all components and if it works correctly:

  • cortex_multikv_mirror_enabled – shows which components have KV store mirroring enabled. All Mimir components should start mirroring to secondary KV store reloading runtime configuration.
  • rate(cortex_multikv_mirror_writes_total[1m]) – shows rate of writes to secondary KV store in writes per second.
  • rate(cortex_multikv_mirror_write_errors_total[1m]) – shows rate of write errors to secondary KV store, in errors per second.

After mirroring is enabled, you should see a key for each Mimir hash ring in the Memberlist cluster information admin page. See list of components that use hash ring.

Step 3: Switch Primary and Secondary store

jsonnet
{
  _config+:: {
    memberlist_ring_enabled: true,
    multikv_migration_enabled: true,
    multikv_mirror_enabled: true,
    multikv_switch_primary_secondary: true,  // Changed in this step.
  }
}

This change will switch primary and secondary stores as used by multi KV. From this point on Mimir components will use memberlist as primary KV store, and they will mirror updates to Consul. This step does not require restart of Mimir components.

To see if all components started to use memberlist as primary store, please watch cortex_multikv_primary_store metric.

Step 4: Disable mirroring to Consul

jsonnet
{
  _config+:: {
    memberlist_ring_enabled: true,
    multikv_migration_enabled: true,
    multikv_mirror_enabled: false,  // Changed in this step.
    multikv_switch_primary_secondary: true,
  }
}

This step does not require restart of any Mimir component. After applying the change components will stop writing ring updates to Consul, and will only use memberlist. You can watch cortex_multikv_mirror_enabled metric to see if all components have picked up updated configuration.

Step 5: Disable multi KV Store

jsonnet
{
  _config+:: {
    memberlist_ring_enabled: true,
    multikv_migration_enabled: false,  // Changed in this step.
    multikv_mirror_enabled: false,
    multikv_switch_primary_secondary: true,
    multikv_migration_teardown: true,  // Added in this step.
  }
}

This configuration change will cause a new rollout of all components. After the restart components will no longer use multi KV store and will be configured to use memberlist only. We use multikv_migration_teardown to preserve runtime configuration for multi KV store for components that haven’t restarted yet.

All cortex_multikv_* metrics are only exposed by components that use multi KV store. As components restart, these metrics will disappear.

Note: setting multikv_migration_enabled: false while keeping memberlist_ring_enabled: true will also remove Consul! That’s expected, since Consul is not used anymore – mirroring to it was disabled in step 4.

If you need to keep consul running, you can explicitly set consul_enabled: true in _config.

Step 6: Cleanup

We have successfully migrated Mimir cluster from using Consul to memberlist without any downtime! As a final step, we can remove all migration-related config options:

  • multikv_migration_enabled
  • multikv_mirror_enabled
  • multikv_switch_primary_secondary
  • multikv_migration_teardown

Our final memberlist configuration will be:

jsonnet
{
  _config+:: {
    memberlist_ring_enabled: true,
  }
}

This will not trigger new restart of Mimir components. After applying this change, you are finished.